Опора линии электропередач аттестации 22м 30КН Гр65 СГС стальная с размером фланца 450мм
Certification 22m 30KN Gr65 Steel Power Pole With 4mm Wall Thickness Descripition of material: The material is in accordance with NF EN 10025 Standard and NF EN 10149 Standard,it has the following property. -Yield Strength=355N/mm2 -Toughness remains the same under 20 degrees below zero. -Galvanization is in accordance with NFA35503 Standard Class 1. Galvanization Standard:NFA91121 Average thickness of the galvanization:Not less than 86μm. Manufacture Tolerance -Component
Опора линии электропередач аттестации 24м 24КН Гр65 БВ стальная с толщиной стены 3мм
Dodecagonal 24m 24KN Gr65 Steel Power Tubular Pole with Galvanization Descripition of material: All of our material are purchased from famous mill factory to assure the quality A mill certificate issued by the mill factory with stamp and signature must be provided before unload the material in our factory ,otherwise we have our reason to refuse the material . Before put into production ,all the material must pass the chemical and physical analysis to make sure that they have
Поляк ОЭМ стандартный телескопичный стальной трубчатый для линии передачи энергии проекта
Telescopic Steel Tubular Pole For Power Transmission Line Project Production Process Our factory own advance production line, machine including bending calibration machine, hydraulic plate shears machine, shears machine, slitting machine, 208T hydraulic straightener, etc. All the purpose is to produce good quality steel poles. The fabrication process as cut plate, bending, forming, automatic welding, drill holes, quality check before galvanized, hot dip galvanized and powder
На открытом воздухе опора линии электропередач 20КН Гр65 Додекагонал 24м стальная для передачи энергии
Outdoor Gr65 Dodecagonal 24m 20KN Steel Power Tubular Pole for Power Transmission Descripition of material: All of our material are purchased from famous mill factory to assure the quality A mill certificate issued by the mill factory with stamp and signature must be provided before unload the material in our factory ,otherwise we have our reason to refuse the material . Before put into production ,all the material must pass the chemical and physical analysis to make sure
Поляк 6.5КН К345 полигональный 12М стальной трубчатый с гальванизированием 15 лет гарантии
Q345 Polygonal 12M 6.5KN Steel Tubular Pole With Galvanization Descripition of material: Usually?Q345B/A572,minimum yield strength>=345n/mm2 Q235B/A36,minimum yield strength>=235n/mm2 As well as Hot rolled coil from Q460 ,ASTM573 GR65, GR50 ,SS400, SS490, to ST52- Manufacture Tolerance -Component Length:-25mm to 75mm -Straightness:2mm/m -Twisting degree:1°per 3 meters length -Ovalisation:Maximum is 3% -The average diameter:+/-0.5% -Slip length:+/-150mm Specification: Suit for
Внешний 8КН стальной трубчатый поляк, коммерчески прочность фонарных столбов 355 н/выхода мм2
Outdoor Polygonal 10M 8KN Steel Tubular Pole With Galvanization Descripition of material: Steel The material is in accordance with NF EN 10025 Standard and NF EN 10149 Standard,it has the following property. -Yield Strength=355N/mm2 -Toughness remains the same under 20 degrees below zero. -Galvanization is in accordance with NFA35503 Standard Class 1. Galvanization Standard:NFA91121 Average thickness of the galvanization:Not less than 86μm. Specification: Suit for Electricity
Гр65 Додекагонал электрические трубчатые стальные поляки передающей линии поляка АВСД 1,1
20m 32KN Gr65 Dodecagonal Steel Electric Tubular Pole with Galvanization Descripition of material: The material is in accordance with NF EN 10025 Standard and NF EN 10149 Standard,it has the following property. -Yield Strength=355N/mm2 -Toughness remains the same under 20 degrees below zero. -Galvanization is in accordance with NFA35503 Standard Class 1. Installation -Remove all the equipment on the pole during Assembly. -Circle a sling around th epole shaft of each section.
Поляк электричества 6.5КН Гр50 полигональный 11.8М стальной для передачи энергии
Gr50 Polygonal 11.8M 6.5KN Steel Power Tubular Pole for Power Transmission Descripition of material: Usually?Q345B/A572,minimum yield strength>=345n/mm2 Q235B/A36,minimum yield strength>=235n/mm2 As well as Hot rolled coil from Q460 ,ASTM573 GR65, GR50 ,SS400, SS490, to ST52- Manufacture Tolerance -Component Length:-25mm to 75mm -Straightness:2mm/m -Twisting degree:1°per 3 meters length -Ovalisation:Maximum is 3% -The average diameter:+/-0.5% -Slip length:+/-150mm Specificati
круглый сплющенный стальной трубчатый поляк 132кв для африканской электрической передачи
132kv Round Tapered Steel Tubular Pole For African Electrical Transmission Production Process Our factory own advance production line, machine including bending calibration machine, hydraulic plate shears machine, shears machine, slitting machine, 208T hydraulic straightener, etc. All the purpose is to produce good quality steel poles. The fabrication process as cut plate, bending, forming, automatic welding, drill holes, quality check before galvanized, hot dip galvanized
